🏍️ DIRT BIKE GARAGE

17-Brand Platform • MY 2020–2026
Pro Workshop Manual, Slacker Sag, WP XACT / KYB / Showa Tuning & Multi-Brand Service Architecture
NO ACTIVE BIKE
Active Bike:
📱 How to Read Engine Hours in the Yamaha Power Tuner App:
1. Wake Bike CCU Wi-Fi: Tap the starter button briefly (or turn Main Power ON) so the bike's CCU wakes up, then connect your phone's Wi-Fi to the bike network (CCU-...).
2. Launch App: Tap 📱 Tuner ↗ above (or open Yamaha Power Tuner in Samsung Pop-Up View).
3. Open Monitor: Tap the Diagnosis / Monitor icon (wrench/gauge icon) on the Power Tuner home screen.
4. Read Hours: Tap Vehicle Status (or Operation Data) and read Total Operating Time (Engine Run Time).
5. Log Here: Tap Update ⏱️ above and enter the hours into your Garage tracker.
📋 Multi-Brand Off-Road & MX Coverage Notice
17 Factory Brands • MY 2020–2026 Pre-2020: Custom Manual Baseline
17-Brand Dynamic Workshop Platform: Supports Aprilia, Beta, BMW Motorrad, CFMOTO, Ducati, GasGas, Honda, Husqvarna, Kawasaki, Kove, KTM, Rieju, Royal Enfield, Sherco, Suzuki, Triumph, and Yamaha off-road, enduro, cross-country, motocross, dual-sport, and ADV machines with brand-specific suspension architectures (KYB SSS, WP XACT Air/Closed-Cartridge, Showa, Telelever/Paralever), 4-stroke EFI & 2-stroke premix/TBI modules.
Notice for All Riders: Use the Slacker sag calculator, ergonomic geometry tools, and brand-specific damping/premix calculators as a pro workshop reference, and always verify model-year capacities and fastener torques in your official factory service manual.
⚠️ Verify oil system bleed/screens, fork seal dryness, and front fender bottoming clearance.
Due Soon & Next Upcoming Service (Top 3)
Showing 3 of 12 Intervals
ℹ️ Parts Fitment Notice: Direct MotoSport part links are unavailable for Rieju models. Check your local authorized Rieju dealer for model-specific OEM and aftermarket fitment.
2026 Factory Off-Road Profile
Factory Off-Road & Motocross Specification
Rising-Rate Linkage Rear 250cc 🛒 Shop MotoSport ↗
NGK LMAR8G
Valve Spec (Cold IN / EX)
0.12–0.19 / 0.17–0.24 mm
Gearing (OEM vs Active)
13/51 vs 13/51
Rider & Static Sag
97 mm / 37 mm
Active Tires & Exhaust Installed
🛒 Shop USFS Exhaust / Spark Arrestor ↗
Dunlop MX33
Fuel / Octane Spec
91+ AKI (95+ RON) Premium Unleaded • E10 Max
Fuel Tank Capacity
2.0 gal (7.5 L)
Coolant Capacity & Type
🛒 Shop Powersports Coolant ↗
1.10 L • Silicate-Free Ethylene Glycol 50/50
520 O/X-Ring • 50–60 mm Slack
Battery Chemistry & Charging Warning
🛒 Shop LiFePO4 Battery ↗
12V LiFePO4 Lithium-Ion (Use LiFePO4 Charger Only)
ℹ️ Parts Fitment Notice: Direct MotoSport part links are unavailable for Rieju models. Check your local authorized Rieju dealer for model-specific OEM and aftermarket fitment.
🖥️ WR250F / WR450F Instrument Cluster Quick Reference
Left-Side Vertical Buttons: Top = Button A (Select / Mode) • Bottom = Button B (Reset / Adjust)
📊 Multi-Terrain Suspension Tuning Matrix
All clicker settings are counted outward (counter-clockwise) from gently seated zero (fully clockwise). Click "[Load Preset]" under any terrain column to apply those settings.
Parameter & Adjuster Location OEM Baseline ★ Current Setup Sand & Whoops
Hard Pack & Clay
Mud & Slick
Rocks & Woods
Desert & GP
Fork Compression
📍 TOP Cap / Lower Adjuster
12 clicks 12 clicks 9 clicks (Stiff) 14 clicks (Soft) 13 clicks 15 clicks (Plush) 10 clicks (Firm)
Fork Rebound
📍 BOTTOM Axle Lug / Top Cap
12 clicks 12 clicks 10 clicks (Slow) 12 clicks 13 clicks 14 clicks (Fast) 11 clicks
Fork Clamp Height
Tube Above Top Clamp
5.0 mm 5.0 mm 2.0 mm 7.0 mm 5.0 mm 7.0 mm 3.0 mm
Rear Lowering Offset
Linkage / PDS Drop
0.0 mm (Stock) 0.0 mm (Stock) 0.0 mm 0.0 mm (Stock) 0.0 mm (Stock) 0.0 mm (Stock) 0.0 mm
Shock Low-Spd Comp
📍 Upper Reservoir Adjuster
12 clicks 12 clicks 10 clicks 14 clicks 13 clicks 15 clicks 11 clicks
Shock High-Spd Comp
📍 Upper Hex / Outer Dial
1.50 turns 1.50 turns 1.25 turns 1.75 turns 1.50 turns 1.875 turns 1.375 turns
Shock Rebound
📍 Bottom Clevis Screw
12 clicks 12 clicks 10 clicks 12 clicks 13 clicks 13 clicks 11 clicks
Rider Sag Target
Standing Attack Stance
100–105 mm 103 mm 105 mm 100–103 mm 100–103 mm 100–103 mm 103–105 mm
Tire PSI (Front / Rear)
Cold Pressure
14.5 / 14.5 PSI 14.5 / 14.5 PSI 13.5 / 12.0 PSI 14.5 / 14.0 PSI 12.5 / 11.5 PSI 13.0 / 12.0 PSI 14.5 / 13.5 PSI
📍 Suspension Adjuster Locations, Air Bleeders & OEM Spring Rates
Rising-Rate Linkage Rear Travel: 300mm F / 305mm R
Fork Comp & Air Bleed (TOP)
Top Fork Cap Dial / Clicker on top of fork caps. The Air Bleed Screw sits directly beside the dial—bleed on stand before every ride!
Fork Rebound (BOTTOM Lug)
Bottom Axle Lug Adjuster (exposed flathead screw or tool-free clicker dial under axle lug). Wipe mud out before turning.
Shock LSC & HSC (UPPER)
Upper shock reservoir. Center adjuster is LSC (clicks). Outer hex/dial is HSC (turns/clicks out).
Shock Rebound (BOTTOM Clevis)
Adjuster on lower shock clevis above the linkage relay arm. Controls rear extension speed.
OEM Spring Rates, Rear Suspension Architecture & Sag Target
📐 Chassis Stance, Lowering Link, Seat & Footpeg Ergonomics
Rear Linkage, Fork Projection, Guts / Seat Concepts & Footpegs
Calculates front-to-rear pitch, rider triangle legroom, and mechanical tire clearance
OEM Standard (0mm Drop)
mm
mm
Dealer OEM baseline: 8.0 mm
Chassis & Ergonomic Balance Analysis
Analyzing stance...
🚨 SEVERE INJURY WARNING: FRONT TIRE TO MUDGUARD CLEARANCE
DO NOT LOWER THE FRONT END EXCESSIVELY: Sliding fork tubes up through the triple clamps reduces clearance between the front tire and the front mudguard (fender). Raising forks too far—or combining raised forks with taller 90/100-21 front tires—can cause tire knobs to strike and lock solidly against the front mudguard at full bottoming. Never exceed 19 N·m (14 ft-lb) on lower triple clamp pinch bolts.
⏱️ Slacker Digital Sag Scale Quick-Start Guide
Pro Digital Workflow
1. Zero Baseline on Stand (L1)
Clip Slacker magnetic mount to rear axle, hook retractable cable to rear fender clip, place bike on stand with rear wheel unweighted, and press Zero.
2. Free / Static Sag (L2)
Set bike on level ground balanced upright under its own weight. Read Slacker display directly.
WR/FX Target: 30–40 mm | YZ Moto: 35–45 mm
3. Standing Rider Sag (L3)
In full riding gear, stand centered on the footpegs in attack posture while an assistant balances the front wheel.
WR/FX Target: 90–100 mm | YZ Moto: 100–105 mm
📐 Digital Sag Calculator & Diagnostic Engine (Target: 90 – 100 mm)
mm
Expected Free Sag Target: 30 – 40 mm
mm
WR/FX Target: 90 – 100 mm (Woods Sweet Spot: 95 – 98 mm)
Rider Sag 97 mm
Static / Free Sag 37 mm
✅ RIDER SAG PERFECTLY DIALED (97 MM)
🛠️ Trail Damping Symptom Solver (12 Clicker Scenarios)
REAR END KICKING / POGO REMEDY
Tire Specification Vault: OEM Factory vs. Installed Tires
Tire Spec OEM Factory Equipped (WR250F) ★ Current Installed Tires (Editable)
Front Tire Brand & ModelDunlop Geomax MX33Dunlop Geomax MX33
Front Tire Size80/100-21 (51M)80/100-21
Rear Tire Brand & ModelDunlop Geomax MX33Dunlop Geomax MX33
Rear Tire Size110/100-18 (64M)110/100-18
Terrain / Compound NotesSoft-to-Intermediate Factory SpecWoods / Intermediate (13.5 PSI)
Installed At Engine Hour0.0 hrs0.0 hrs
⚠️ Tire Sizing & Rim Lock Safety
At off-road pressures (11–13.5 PSI), torque front and rear rim locks to 13 N·m (9.6 ft-lb) so the tire cannot spin and shear the valve stem. Re-verify front fender bottoming clearance if installing a taller 90/100-21 front tire!
ℹ️ Parts Fitment Notice: Direct MotoSport part links are unavailable for Rieju models. Check your local authorized Rieju dealer for model-specific OEM and aftermarket fitment.
Side-by-Side Gearing: OEM Factory vs. Current Installed
OEM Factory Baseline (Stock)
Dealer Stock
Front / Rear Sprockets
13T / 51T
Final Drive Ratio
3.923 : 1
OEM Chain & Slack Spec
520 O/X-Ring • 50–60 mm Slack
Current Installed Setup
Active
Active Final Ratio & Torque Delta
3.923 : 1 (0.0% Torque)
Chain Spec & Length
114 Links (520 X-Ring)
ℹ️ Parts Fitment Notice: Direct MotoSport part links are unavailable for Rieju models. Check your local authorized Rieju dealer for model-specific OEM and aftermarket fitment.
Drivetrain & Chain Buffer Analysis
🔥 Exhaust System Vault: OEM vs. FMF Slip-Ons & Full Systems
Exhaust, Spark Arrestor & EFI Mapping Analysis
ℹ️ Parts Fitment Notice: Direct MotoSport part links are unavailable for Rieju models. Check your local authorized Rieju dealer for model-specific OEM and aftermarket fitment.
🌀 Throttle Cam Reference: G2 Throttle Tamer vs. Quick-Turn
Throttle Cam TypeCam Pulley GeometryEffect on Bike Feel & TractionBest Terrain
G2 Ergonomics Throttle Tamer Non-linear progressive radius (smaller initial pull radius from 0–25% throttle, ramping to 1:1 at WOT) Requires slightly more wrist rotation for the first 1/4 throttle opening—eliminates jerky off-idle EFI snap over rocks and roots and reduces arm pump Technical singletrack, wet roots, rock gardens, steep rock ledges
Quick-Turn / Aggressive Cam Oversized circular/progressive pulley that pulls more cable per degree of twist Reaches wide-open throttle with less wrist rotation; makes low-to-mid hit feel sharper and more immediate Deep sand washes, motocross tracks, desert whoops
OEM Standard 1:1 Cam Linear constant-radius pulley Direct 1:1 proportional butterfly opening throughout twist range General trail riding, fire roads, dual-track
📲 Engine Tuning App & 4×4 FI / IG Mapping Grids
🌲 FORESTRY V1 / V2 — TECHNICAL SINGLETRACK & ROCK CRAWLING
⛽ Fuel Injection (FI %) — 4×4 Grid (100% Top → 10% Bottom)
⚡ Ignition Timing (IG °) — 4×4 Grid (100% Top → 10% Bottom)
💡 How to Enter in Power Tuner App: Connect to bike CCU Wi-Fi → open Tuning → 4×4 Grid View (100% throttle top row, 10% throttle bottom row) → input the FI (%) and IG (°) numbers above → tap the Send to ECU (Upload) icon in the top-right corner.
Diagnostic DTC Fault Codes
CodeCircuit / SensorSymptomAction
12Crankshaft Position SensorNo spark / will not startInspect pickup coil harness & stator plug
13 / 14Intake Air Pressure SensorRough idle, tip-in bogCheck throttle body sensor vacuum port
15Throttle Position Sensor (TPS)Erratic throttle responseInspect 3-pin TPS coupler
21Coolant Temp SensorHard cold start, fan issueCheck sensor on cylinder head jacket
30Lean Angle Sensor (Tip-Over)Engine cuts out after fallCycle power switch OFF/ON once upright
33Ignition Stick Coil PrimaryNo spark, sudden stallCheck primary clip on top of stick coil
46Charging System VoltageMIL light, battery drainVerify 14.0–14.5V charging at 5,000 RPM
⏱️ Full Service Interval Schedule (All 12 Intervals)
12 Tracked Intervals
ℹ️ Parts Fitment Notice: Direct MotoSport part links are unavailable for Rieju models. Check your local authorized Rieju dealer for model-specific OEM and aftermarket fitment.
Pre-Ride Cockpit, Fork Bleeders, Seals, Tires & Chassis Checklist
Air Filter Inventory & Rotation Tracker
Tap any filter card to rotate between Installed in Bike, Dirty in Wash Bucket, and Clean & Oiled in Bag.
ℹ️ Parts Fitment Notice: Direct MotoSport part links are unavailable for Rieju models. Check your local authorized Rieju dealer for model-specific OEM and aftermarket fitment.
48-Hour Race & Event Garage Prep
Discipline Prep
Truck / Paddock Spares & Tool Kit Checklist
🚚 Truck Loading, Pit Shade & Tailgate Comfort Checklist
🧼 Post-Ride Wash & Care Routine (All Bikes)
❄️ Winterizing & Off-Season Storage Checklist (All Bikes)
Factory Service & Owner's Manual Locker (Offline PDF)
📚 Factory Service & Owner's Manual Locker (Offline PDF)
Per-bike offline storage powered by IndexedDB (supports 20–100+ MB factory PDF manuals at the trailhead).
No PDF Attached
Stored Manual File
None attached for this bike
Offline Storage Size
-- MB
Saved Date
--
🌐 Download Official Factory Manual (OEM Portal) ↗
💡 Yamaha & OEM Portal Tip: Select ‘Motorcycles / Off-Road’ and enter your model year (e.g., 2025 WR250F) to download your PDF manual, then upload it above.
Factory Shop Procedures & Critical Safety Warnings (8 Guides)
ℹ️ Parts Fitment Notice: Direct MotoSport part links are unavailable for Rieju models. Check your local authorized Rieju dealer for model-specific OEM and aftermarket fitment.
🛞 Spoke Maintenance, Torque Wrench Settings & 3-Step Sequence
Every 5.0 Hrs / Pre-Ride ▾
Spoke Torque Spec
30 – 35 in-lb (3.4 – 4.0 N·m)
Absolute Limit
44 in-lb (5.0 N·m Max)
Required Tool
Spoke Torque Wrench
Nipple Head Sizes
6.1mm, 6.3mm, 6.8mm, 6.9mm
🚨 WARNING: INCH-POUNDS VS. FOOT-POUNDS & SPROCKET BOLTS
NEVER TORQUE SPOKES TO FOOT-POUNDS (ft-lb): Spoke nipples use small threads. The proper setting is 30 to 35 inch-pounds (3.4 to 4.0 N·m / 2.2 to 2.9 ft-lb). Applying 35 foot-pounds (420 in-lb) will strip the nipple or snap the spoke! Do not confuse spokes with rear sprocket bolts (25 ft-lb / 34 N·m).
  1. Acoustic Ping Test: Tap each spoke mid-span with a metal wrench. Tight spokes emit a clear high-pitched "ping"; loose spokes emit a dull "thud."
  2. Set Spoke Torque Wrench: Adjust your spoke torque wrench to 30–35 in-lb and seat the proper jaw head squarely on the nipple.
  3. The 3-Step Tightening Sequence: Start at the valve stem or rim lock. Pass 1: Tighten every third spoke around the wheel until it clicks. Pass 2: Advance one spoke and tighten every third spoke. Pass 3: Tighten the final third set of spokes. This 3-pass sequence keeps the rim hoop true and concentric.
🔱 Fork Air Bleed, Seal Cleaning & Oil Service
Every Ride / 40.0 Hrs ▾
Fork Architecture
KYB SSS 48mm Coil
Top Cap Bleed & Adjusters
M5 Bleed Screw + Top Comp / Bottom Reb
Upper / Lower Clamp Torque
21 N·m / 19 N·m
Seal Cleaner Tool
0.15 mm Plastic Seal Doctor
🚨 FRONT BRAKE CONTAMINATION WARNING (LEFT FORK SEAL)
NEVER RIDE WITH A LEAKING LEFT FORK SEAL: Oil weeping down the left fork leg drips directly onto the front brake rotor and pads, causing a sudden loss of front braking power!
  1. Pre-Ride Top-Cap Air Bleed (0 PSI Unweighted): Place the bike on a center stand with the front wheel completely off the ground. Locate the small M5 air bleed screw on the top of each fork cap and back it out slowly (or press push-button bleeders) to vent trapped air pressure to atmospheric 0 PSI.
  2. Rescuing a Weeping Fork Seal: Pry the black outer rubber dust wiper down with a plastic tool, flush with contact cleaner, slide a 0.15mm plastic Seal Doctor under the inner oil seal lip to hook out trapped grit, grease lightly, and snap the dust wiper back up.
🛢️ Recommended Engine / Gearbox Oil, Filter & Bleed Service
7.5 / 15.0 Hrs ▾
Oil Change (Drain Only)
0.73 L (730 mL)
With Filter / Gearbox Fill
0.75 L (750 mL)
Dry Engine Overhaul
0.95 L (950 mL)
Drain / Filter / Bleed Torques
20 N·m / 10 N·m / 7.2 ft-lbs (10 N·m)
  1. Drain & Filter: Warm engine 2–3 min, remove bottom drain bolt (torque 20 N·m / 15 ft-lb with fresh crush washer). Inspect oil screens or install oil filter with open rubber grommet facing inward; torque cover bolts to 10 N·m (7.2 ft-lbs).
  2. Mandatory Oil Gallery Weep Bleed (Check Bolt): Locate the M6 oil gallery check/bleed bolt (8mm hex bolt) on the left side of the engine (Note: always verify exact engine-side placement by model year in your factory service manual). Crack the bolt 1/2 turn counter-clockwise, start the engine at idle until oil steadily weeps out (within 5–10 sec) to confirm oil pressure to the top end, shut off immediately, and torque to 7.2 ft-lbs (10 N·m).
🎯 Cold Valve Clearance / Exhaust Power Valve Inspection
Every 30.0 Hrs ▾
Intake / Power Valve Spec
0.12 – 0.19 mm
Exhaust Clearance (Cold)
0.17 – 0.24 mm
Valve Cover Bolts
10 N·m (7.4 ft-lb)
Last Recorded Check
Baseline 0.0h
Recorded Valve Clearances (L / R)
🔗 Rear Shock Linkage / PDS & Swingarm Pivot Bearing Grease
15–20 Hrs ▾
Remove lower shock clevis bolt (60 N·m), linkage relay/pull-rod bolts (80 N·m), and swingarm pivot shaft (85 N·m). Clean collars and pack needle bearings with waterproof marine/moly grease. Inspect top front rubber chain slider for wear.
⚡ Spark Plug Service (Dual Air-Blast Method)
15.0 Hrs ▾
Active OEM Spark Plug
NGK LMAR8G
Electrode Gap & Torque
0.7–0.8 mm • 13 N·m (9.6 ft-lb)
Blast compressed air around the head before pulling the ignition coil/cap, and blast down the open spark plug well again before loosening the plug so sand never drops into the cylinder! Thread new plug by hand before torquing.
🛑 Hydraulic Brakes, Clutch Freeplay & Air Filter Care
5–20 Hrs ▾
• Hydraulic Brakes: Min pad lining 1.0 mm (2.0 mm race). Bleeder torque: 6 N·m; Banjo bolts: 30 N·m. Leave air gap in reservoir.
• Clutch Freeplay: Maintain 8–13 mm at cable lever ball end (or inspect hydraulic clutch fluid level).
• Foam Air Filter: Stuff a clean microfiber rag into the intake bellmouth before wiping the airbox rim so dirt cannot drop into the intake tract.
🌡️ Cooling System Bleed, USFS Spark Arrestor & LiFePO4 Battery
25.0 Hrs ▾
🚨 PUBLIC LAND SPARK ARRESTOR LAW & LITHIUM BATTERY WARNING
1. Public Land Spark Arrestor Law: Factory motocross and cross-country competition mufflers do NOT contain a USFS spark arrestor. Riding on U.S. Forest Service or BLM land without a certified spark arrestor (such as an OEM enduro spark-arrested muffler, FMF Q4 Hex / TurbineCore 2, or USFS screen insert) carries heavy federal fines and wildfire liability.
2. LiFePO4 Battery: Use only a Lithium Iron Phosphate (LiFePO4) charger—never use a lead-acid desulfating charger (>15V).
🔧 Pro Workshop Torque Matrix (2020–2026)
Model-Specific Fastener Torque Specifications
Always double-check critical engine & chassis torques against your official OEM service manual.
Multi-Brand Baseline
CategoryFastener / ComponentThread / SpecTorque (Metric / Imperial)Safety & Shop Notes
Ownership & Purchase Provenance (Active Bike)
Purchase Date
--
Hours at Purchase
0.0 hrs
Your Run-Time Logged
0.0 hrs
Purchase Price / Value
--
VIN / Frame Serial Number
--
Dealer / Setup Notes
--
Prior Maintenance & Modification Archive
DateHoursWork Performed / ModificationParts / CostBy
Automated Tracker Service Logbook
⚙️ App Settings & Shopping Region
Parts & Gear Store Region
Auto-detected locally via browser timezone & language (zero network requests or tracking). US riders see Amazon + US retailers (MotoSport, Yamaha Online Parts, SIDI); International riders see Amazon OneLink only.
Detected: United States
Garage Data Backup & Restore
⚠️ Danger Zone — Irreversible Garage Actions
📋 Multi-Brand Off-Road & MX Coverage Notice
17 Factory Brands • MY 2020–2026 Pre-2020: Custom Manual Baseline
17-Brand Dynamic Workshop Platform: Supports Aprilia, Beta, BMW Motorrad, CFMOTO, Ducati, GasGas, Honda, Husqvarna, Kawasaki, Kove, KTM, Rieju, Royal Enfield, Sherco, Suzuki, Triumph, and Yamaha off-road, enduro, cross-country, motocross, dual-sport, and ADV machines with brand-specific suspension architectures (KYB SSS, WP XACT Air/Closed-Cartridge, Showa, Telelever/Paralever), 4-stroke EFI & 2-stroke premix/TBI modules.
Notice for All Riders: Use the Slacker sag calculator, ergonomic geometry tools, and brand-specific damping/premix calculators as a pro workshop reference, and always verify model-year capacities and fastener torques in your official factory service manual.
⚠️ Verify oil system bleed/screens, fork seal dryness, and front fender bottoming clearance.
📖 Step-by-Step App User Guide (How to Use Dirt Bike Garage)
  1. Step 1 — Add & Switch Your Bikes: Click [+ Add Bike] in the top garage bar to add multiple dirt bikes, dual-sports, or ADV machines across all 17 brands (2020–2026) — or choose Pre-2020 / Custom Build for older bikes — and use [⚙️ Profile] to customize your bike's nickname, suspension specs, or rider weight. Switch between bikes anytime using the ACTIVE BIKE dropdown, or click [🗑️ Delete Bike] anytime to remove a sold or unwanted bike.
  2. Step 2 — Log Engine Hours After Every Ride: Use the quick-add buttons (+0.5h, +1.0h) or type your exact hour-meter reading into the top bar and click [Save Hours]. Every service interval across the app automatically recalculates remaining hours.
  3. Step 3 — Track Maintenance & Reset Service Intervals: Open [⏱️ Dashboard] to see color-coded status bars (Green = Good, Yellow = Due Soon, Red = Overdue) for oil changes, air filters, valve checks, and top-ends. Click Done ✔️ after servicing an item to log it to your service history and reset its countdown timer.
  4. Step 4 — Dial In Sag, Clickers, Gearing & Torque: Use [🏁 Pre-Ride & Race Prep] for discipline-aware MX/Enduro/Trail checklists, truck loading, and winterizing; [⚙️ Suspension Matrix] for Slacker/manual sag math and saving your track/trail clicker baseline; [🛞 Tires, Gearing & EFI] for sprocket ratios and premix/mapping; and [🔧 Torque Matrix] + [📖 Shop Guides] for fastener specs and step-by-step DIY procedures.
  5. Step 5 — Backup & Export Your Garage Records: Open [📋 History & Garage] to view your complete service log, export a JSON backup file (recommended before clearing browser data), or restore your garage on a new phone.
⚠️ Workshop Safety Rules & Legal Disclaimers
  1. Fork M5 Air Bleed (Unweighted): Always bleed fork top-cap M5 air screws with the front wheel unweighted on a center stand before riding so trapped chamber pressure returns to atmospheric 0 PSI.
  2. Suspension Clicker Zero Reference: Always count damping clicks outward (counter-clockwise) from gently seated zero (clockwise—never force adjusters tight).
  3. Sag Before Clickers: Set standing rider sag in full gear before adjusting damping clickers, and verify Static / Free Sag to confirm your shock spring rate matches your geared weight.
  4. Spoke Torque Wrench (30–35 in-lb): Always set your spoke torque wrench to 30–35 in-lb (3.4–4.0 N·m) using the 3-step alternating sequence. Never confuse inch-pounds with foot-pounds!
⚖️ LEGAL DISCLAIMER & ASSUMPTION OF RISK
Provided strictly "AS IS" for informational reference across 2020–2026 off-road, motocross, enduro, trail, dual-sport, and adventure platforms (owners of pre-2020 or custom builds must verify all capacities and torque specifications in their official factory service manual). You assume all risks associated with servicing, modifying, or riding your motorcycle. Always physically verify front tire-to-fender clearance at full bottoming when raising fork tubes or changing tire aspect ratios. Independent commercial product by Inxellence LLC; not affiliated with Aprilia, Beta, BMW Motorrad, CFMOTO, Ducati, GasGas, Honda, Husqvarna, Kawasaki, Kove, KTM, Rieju, Royal Enfield, Sherco, Suzuki, Triumph, Yamaha, FMF, Guts Racing, Seat Concepts, G2 Ergonomics, MotoSport, Yamaha Online Parts, SIDI, or Slacker.
🤝 AFFILIATE & PARTNER DISCLOSURE
Affiliate Disclosure (FTC): Dirt Bike Garage (dirtbikegarageapp.com, operated by Inxellence LLC) participates in Impact.com affiliate programs with approved powersports partners including MotoSport, Yamaha Online Parts, and SIDI, as well as Amazon Associates and general retailer affiliate programs. As an Amazon Associate, Inxellence LLC earns from qualifying purchases. When you tap optional outbound parts, tool, or gear links, a referral cookie may be set so Inxellence LLC can earn a small commission on qualifying purchases at zero extra cost to the rider. See our Privacy Policy & Affiliate Disclosure.
🪖 Goggles-First Protective Gear Matrix (3-Discipline Standard)
🥽 Goggles-First Eye Protection Standard (All Off-Road Disciplines)
Full-seal dirt bike goggles are the primary eye-protection standard across Motocross, Hard Enduro, Woods, and Trail riding to block high-speed roost, whipping branches, dust, and mud. Carry spare lenses (or tear-offs/roll-offs for MX); wrap-around ANSI safety glasses are noted strictly as a secondary hot/slow technical backup when climbing sustained 1st-gear rock sections.
🏁 Motocross (MX) Track & Gate Drops
Primary Eye Protection (Goggles) MX goggles fitted with laminated tear-offs or roll-off film systems + spare pre-prepped clear/tinted lenses for roost & wet clay.
Helmet & Neck Support ECE 22.06 rotational-impact helmet (MIPS / 360° Turbine) paired with an articulated neck brace / cervical collar.
Upper Torso Armor Lightweight vented roost / chest & back protector (worn over or under jersey) for high-speed dirt clod & bar impacts.
Knees, Boots & Pants Articulated carbon/composite knee braces (ACL/MCL torsional support), stiff supportive MX-sole boots for flat landings, and in-the-boot MX pants.
Hydration Carry Insulated paddock water bottles between motos (save backpack weight for enduro loops).
🌲 Enduro / Hard Enduro / Woods Tight Trees & Tech
Primary Eye Protection (Goggles) Goggles with anti-fog dual-pane / vented lenses + clear or high-contrast amber lenses for deep timber shade & creek glare. (Wrap-around safety glasses only as a secondary slow-tech climb option.)
Helmet & Neck Support Lightweight ventilated ECE 22.06 shell + neck brace compatible strap clearance for steep log/rock drops.
Upper Torso Armor Breathable CE Level 1 / Level 2 full-torso impact armor shirt (chest, spine, shoulder, elbow pads) against branches, rocks & low-speed get-offs.
Knees, Boots & Pants Articulated knee braces (or rugged CE knee/shin guards), grippy lugged enduro-sole boots for pushing on wet logs/rocks, and over-the-boot trail pants to shed water & mud.
Hydration & Tool Carry No-bounce hydration backpack (2.0–3.0 L bladder) or waist / fanny pack carrying bottles, snacks, tools & SOS beacon.
🏔️ Trail / Dual-Sport Backcountry Miles
Primary Eye Protection (Goggles) Goggles with anti-fog dual-pane / vented lenses + photochromic, amber, or spare clear lens for dust, sun-to-shade & cold mornings. (Wrap-around glasses secondary only.)
Helmet & Neck Support ECE 22.06 dual-sport / off-road helmet with peak visor + optional neck brace for high-speed fire roads.
Upper Torso Armor Breathable CE Level 1/2 impact armor shirt (or armored enduro jacket with zip vents for altitude & weather shifts).
Knees, Boots & Pants CE knee/shin guards or knee braces, lugged enduro/adventure-sole boots, and over-the-boot trail pants with zippered vents & cargo pockets.
Hydration & Tool Carry Hydration pack (2.0–3.0 L bladder or dual bottles) + fanny / tool waist pack balancing weight off your shoulders on 60+ mile days.
💧 Day-Ride Hydration & Pack / Fanny-Pack Nutrition Protocol
Dehydration and sodium depletion drop reaction time, thicken forearm blood flow (accelerating arm pump), and trigger late-afternoon quad/calf cramping. Follow this 4-stage trail & moto fueling timeline:
1. 24 Hours Pre-Ride
• Pre-hydrate steadily throughout the day before riding (pale straw urine target).
• Eat a balanced complex-carb & salty dinner; freeze water bottles half-full overnight for cold bladder/cooler staging.
2. Ride Morning (60–90m Out)
• Drink 16–20 oz water mixed with 500 mg sodium electrolytes.
• Eat low-fiber steady carbs + light protein (oats, eggs, banana, toast) so stomach settles before boots-on.
3. On-Trail / Moto Fueling
• Sip 16–32 oz/hr fluid dosed at 500–1,000 mg sodium per 32 oz (fights arm pump & cramps).
• Pack crush-proof pack / fanny-pack snacks: energy chews, salted pretzels, PB&J halves, jerky & fig/cracker bars every 45–60 min.
4. Post-Ride Recovery
• Within 45 min back at the truck, hit shade & drink 20–24 oz cold water/electrolytes per pound lost.
• Consume a 3:1 carb-to-protein meal/shake to replenish glycogen & stop post-ride soreness.
Saved to Device